|EZ Heat Model No.||Voltage||Description||Part Number||Price||Buy|
|EZ 270||110v||E-Z Heat Engine Heater 3"x5-3/4"x1/32" pad|
Use on flat oil sump surface
|EZ 360||110v||E-Z Heat Engine Heater 5"dia circle x 1/32" pad|
Use on round kidney shaped oil sumps
|EZ 440||110v||E-Z Heat Engine Heater 4"x4"x1/32" pad|
|EZ 441||110v||E-Z Heat Engine Heater 3-7/8"x5"x1/32" pad|
|EZ 441||220v||E-Z Heat Engine Heater 3-7/8"x5"x1/32" pad. No plug included.|
|EZ 442||110v||E-Z Heat Engine Heater 2-1/4"x13"x1/32" pad|
|EZ 470||110v||E-Z Heat Engine Heater|
|EZ 540||110v||E-Z Heat Engine Heater (1) 3"x5-3/4"x1/32 & (1) 3"x4"x1/32"|
|EZ 540||220v||E-Z Heat Engine Heater (1) 3"x5-3/4"x1/32 & (1) 3"x4"x1/32" No plug included.|
Note: Please see "Engine Application Guide" Click Here for the correct EZ Heat model number for your application.
Preheating engines for winter operations is at best a miserable chore and at worst can be a disaster for the plane, the pilot & flight operations - until the development of the E-Z Heat Aircraft Engine Heater. The E-Z Heat was designed to provide very efficient engine heating for virtually all propeller driven aircraft. The heaters consist of a flexible synthetic pad that easily conforms to the contours of the oil pan. This pad will heat 12 qts of oil from -40° to +60°F in an hour while using approximately 300 watts of electricity. The heater is 1/32" thick. which enables the immediate heat transfer from heater to engine.
The heaters are thermostatically controlled, so leaving them plugged in overnight means the plane will be ready to go in the morning. Normally, complete pre-heating takes only 3-5 hours for the entire engine to be nice and warm. With this new lighted plug (110V models only, 220V models include no plug to allow for European outlet variance), the owner simply needs to look out the window or peek in the hangar to see if they remembered to plug in their E-Z Heat engine pre-heater. Molded into the male plug end is a newly designed light emitting diode (LED). This LED allows the operator to visually recognize if there is electrical power to the preheat system even from a distance. FAA approved for certificated aircraft.
End your cold weather starting problems and reduce premature engine wear.
E-Z Heat Installation Instructions
| Power Consumption: |
300 watts or less / Thermostatically Controlled
110/120 volts (models 440, 441 and 540 are available in 220 volts).
The adhesive is already on the pad. All you need to do is peel and stick it on! (excluding model 470)
3 to 5 hours on cold soaked engine, although, since unit is thermostatically controlled, it may be left on overnight, or all the time. Cowl covers and prop covers are recommended for extreme cold weather, they also reduce preheat time.
Lite Brite Plug:
With this new lighted plug, the owner simply has to look out the window or peek in the hangar to see if they remembered to plug in their E-Z Heat engine pre-heater! (excluding model 470)
Only 9 ounces!
Convection/conduction, the safest way of heat transfer available. No flames or glowing elements are potential fire hazards.
E-Z Heat Models:
I received this heater unit promptly with good instructions and easy to follow. Easy to install. I have not plugged the unit in as of yet, except to test due to not really any cold weather here yet. Worked well when tested.
6 quarts oil in a C145 Cont. 45deg to 65deg in 15min.
Great little heater, very light, easy to install and puts out a tonne of heat for its size. It heats up the whole engine in half the time that it says.
Perfect fit. Happy!
I installed model 441 on my 172M and it works as advertised. Outside air temp was 10F. I had an engine blanket on and plugged it in overnight. The temp according to the digital sender in my engine monitor said the oil temp was 66F, well within a safe temp for starting. The cylinders also felt warm to the touch and after starting, the engine was quickly up to operating temp. Great product.
Thoroughly impressed. As others have stated this pad will heat the entire engine, cylinders included. Sub-freezing temps in the hangar and my oil temp was 80 with a blanket over the cowl, 65 without blanket. Highly reccomend.
Great product! Very simple to install and to use! Thanks
Nice product, easy to install.
Good product. Edge sealant included. Easy to apply.
Per the supplier: No, a log book entry is not required by an A&P.
Per the supplier: Yes, they can either use the EZ540 or the EZ441 for that engine type.
Per the supplier: No, they do not require field approvals.
It comes on at around 120F and shuts off at around 165F.
Per the supplier: You can leave this on for about a week or two as long as you fly your aircraft at least once or twice a month.
The manufacturer's warranty is 3 years.
Approx 2.4 amps
These are the same units, only difference is the input voltage. The 07-05200 is intended for use with 110v input voltage. The 07-05200-2 is intended for 220v input voltage. 220v input is commonly found in Europe. The USA wall outlets are all 110v.
The heaters can take a slight curve but can not be creased due to the fact that they have heating elements throughout the pad so they can get broken, burning out the pad, if creased or bent to sharply. The round sump will take the 360 which has tabs so that you don't have to bend it.
As long as the paint is in good shape and not chipping or pealing off, you can just stick it on the painted sump.